ONE STOP SHOP FOR ALL THINGS DIY
November 16, 2019
"This post is sponsored by The Home Depot."
I have been putting off building me a desk for some time now, but I finally got around to it. I have been using my kitchen table as my desk in the meantime and I am so glad to be getting out of the kitchen.
I had been looking around for designs for a while and saw this cool design online and just had to re-enact it. Lucky for you, I am sharing these farmhouse desk plans with step-by-step instructions on how to build it.
Now let's get into the nitty gritty!
"There are some affiliate links in this post, meaning I get a small commission if you purchase through these links, at no cost to you. Click Here to read my full disclosure."
"See Detailed Plans for Cut List"
The best part about this build was getting to try out my new DEWALT Atomic 20-Volt Hammer Drill/Impact Combo Kit. I love that it comes with this heavy duty ToughSystem Case.
The case comes packed with a compact impact drill and hammer drill, both 20V brushless tools.
I first used the DEWALT Hammer Drill to drill the pocket holes into the sides of the DIY Desk. I used my Kreg Jig on a 3/4" setting.
After drilling my pocket holes, I attached the middle stretcher pieces to the outer 2x2s using 1 1/4" pocket hole screws and wood glue. Your two desk sides should look something like the following when you're finished.
The top stretcher should be a 1x4 and the bottom stretcher should be a 1x3.
Next was the fun part, adding the decorative V braces. I first made my bottom angled cut and then placed my 1x2 underneath my assembled side and marked my board where I should make the second cut.
Always measure before you cut for the best fit. I did this for both sides.
Then I used my Kreg Jig on a 3/4" setting to drill pocket holes into the V braces and attached them to the assembled sides using 1 1/4" pocket hole screws.
Your assembled sides should look like this once you attach your decorative V braces.
Next, I attached the two assembled sides together by attaching the two stretcher pieces. The top stretcher piece is a 1x4 and the bottom stretcher is 1x3.
I used my Kreg Right Angle Clamps to secure the stretcher pieces so I could screw them into the sides. I used the 1 1/4" pocket hole screws along with wood glue to secure the stretchers into place.
Once the stretchers were in place, I used the same technique to measure the back V braces and attached them using a 1 1/4" pocket hole screws.
Drilling pocket holes on slanted boards can be a little tricky, so just be mindful of where you are drilling your holes.
Now for all of you who thought I had a drawer on this desk, I hate to inform you that this is a faux drawer. Yes, I was being lazy; but luckily for you guys I have added extra steps in the printable plans for those of you who want to add in a drawer. Redemption!
To create my faux drawer, I set the depth on my miter saw to a specific depth so that it would only cut a little above midway on the board. This step was super simple. Then I added a drawer handle to the front, to give the illusion of a drawer.
Once I added the handle, I attached the desk front to the assembled desk using 1 1/4" pocket hole screws along with wood glue.
My Kreg Right Angle Clamps always come in handy. If you are a builder that works alone, I highly recommend these for building.
Lastly, I attached the middle supports to the assembled desk. I made sure to pre-drill holes on the top of the middle supports to be able to secure the top to the desk.
Once I attached the middle supports, I used my circular saw to cut the 24x48 project panel down to size and attached it to the desk using the pre-drilled pocket holes and 1 1/4" pocket hole screws and this beauty is finished.
once I finished building the desk, I went back through and filled in all the pocket holes to give it a seamless look. Check out my tutorial on filling pocket holes to see how I got the job done. Be sure to check out the farmhouse desk plans for all the measurements.
Your photo upload was successful. Please submit the following so that we may review and post your submission:
February 03, 2021
January 28, 2021
January 20, 2021
Sign up to get the latest on sales, new releases and more …