June 08, 2018
I have been dying to add a little design to my front doorway, and I knew this would be the perfect project to get it jump started. This Zinc Flower Pot was so fun and easy to make and it definitely exceeded my expectations.
This review is sponsored by the Home Depot as a part of The Home Depot's Pro-Spective Campaign.
Not only was this a fun project, but I was able to complete it in less than two hours. I'm a sucker for a quick project. I have had this project in my mind for a little over a year, so it's about time I actually got it done.
I have a lot more plans for making my doorway look more appealing but this little DIY zinc flower pot really made big difference.
There are some affiliate links in this post, meaning I get a small commission if you purchase through these links, at no cost to you. Click Here to read my full disclosure.
10 Qt. Galvenized Steel Pail
Amy Howard At Home Zinc Solution
Rustoleum Chalk Paint - Linen White
Makita Impact Driver
Bosch Daredevil Carbide Bits
So let's take a quick look at where we started. Can you believe this is how the metal pail looked before? I mean I can because I made it haha but if I didn't I would totally be surprised.
Luckily for you guys, I video'd the process of making the pot, but for those of you who like to read, Im sharing all of the details below!
Now let's get to it!
So the first and probably most important step is to clean off the pail. The Zinc solution works a lot better when the pail is completely clean and free of grease. One thing you want to make sure you do also is to get all of the sticky solution off of any stickers stuck to the pail.
Is it just me, or does anybody else hate when stores put labels on an item in the worst spot possible. How about putting the sticker on the bottom? So I don't have to spend 30 minutes trying to get the sticker off. Anywho! thats my rant for today.
To help get the stickers completely off, I used windex and that seemed to help a lot.
I was so ready for this step because I have been wanting to try this Zinc Solution out for a while. It's been sitting in my house collecting dust and I finally decided to try it out.
To apply the solution, I poured a little bit in a red solo cup and used a regular was rag to apply to the bucket pail.
When I first started applying the solution, I realized it wasn't really turning colors, but after about 2 or 3 minutes of the solution really settling in, I could tell the pail was starting to turn color. So patience, young grasshopper, the solutions works.
I applied the solution for about 10 minutes and it didn't take a lot of it to turn the pail. If I had to guess, I could probably do this project to 6 or 7 pails of this size with one bottle of solution, if not more.
After applying the Zin solution to the zinc flower pot, I let it sit for about 25 minutes and then started applying the frog tape. I have always had good experiences with frog tape while painting walls, so I figured it would be good for this project.
Big lessons learned for this part of the project was the ridges on the pail. I didn't press down the tape well enough in the ridges and I got some bleed through because of it. AKA I was rushing from the excitement of wanting to finish. Don't be like me! Take your time and get that tape down right!
It also may be easier to tape the pail if you are trying another design as well.
After taping the zinc flower pot down, I starting painting the pail bucket with chalk paint. I opted to use chalk paint because its thick, and it drys quickly. I am a lover of chalk paint also, so I may be biased.
I have always had a good experience with Rustoleum chalk paint and it is a little cheaper than my beloved Annie Sloan so I would definitely recommend it for people looking for chalk paints.
Because I plain on potting this bucket pail, I wanted to add a couple of drainage holes to the bottom. So I used my Makita Impact Driver coupled with my Bosch Carbide Drill Bits to get the job done.
The Makita Impact Driver has a powerful brushless motor that delivers 1,500 in.lbs. of max torque and runs cooler and more efficiently for longer life and the Bosch Multi-Purpose Carbide Drill Bits are used for multi-purpose applications like tile, masonry, wood, metal and concrete. Their sharp diamond-ground edges help deliver high drilling speed on hard materials like this bucket pail. It defintely did it's job here.
and the last and final step....Pot the plant and Enjoy!
I wouldn't be happier with how this DIY Zinc Flower Pot turned out. I'm sure this won't be the last one I make and I hope you guys enjoyed this project. Leave a comment below and let me know what you think?
If you enjoyed this project, don't forget to Pin it!
Thanks for reading guys! XOXO Ashley
I acknowledge that the Home Depot is partnering with me to participate in the THD Pro-Spective Tool Review Program. As a part of the program, I am receiving compensation in the form of products and services, for the purposes of promoting The Home Depot. All expressed opinions and experiences are my own. My post complies with the Word of Mouth Marketing Association (WOMMA) Ethics Code and applicable Federal Trade Commission guidelines.
September 10, 2018
July 16, 2018
July 06, 2018
Sign up to get the latest on sales, new releases and more …