DIY Plate Rack
"A plate rack with a unique design."
I am super excited about sharing this build. This DIY plate rack has been on my long list of "things I need to build" for a while and I'm glad to finally mark it off the list.
"This post is sponsored by the Home Depot as a part of The Home Depot's Pro-Spective Campaign."
I am a big fan of any build that gives me some extra storage in my home and it being something stylish is and extra plus. This was a quick, fun build I was able to tackle in one afternoon and I am excited to share my process of building it.
There are some affiliate links in this post, meaning I get a small commission if you purchase through these links, at no cost to you. Click Here to read my full disclosure.
The best part about this build is that I actually had the time to film it, so if my instructions get a little confusing, please feel free to check out my build video for additional help. Here it is:
2 - 1x6 @ 6ft
1 - 1x2 @ 6ft
1 - 1x4 @ 6ft
1 1/4" Pocket Hole Screws
Danish Oil - Walnut
DAP Rapid Fuse Glue
2 - 1x6 @ 33"
1 - 1x6 @ 22"
3 - 1x4 @ 22"
2 - 1x2 @ 22"
Step 1: First I free handed the pattern for the coat rack sides (1x6 - 33") and then used my Ryobi brushless jigsaw to cut out the patterns on both sides.
The Ryobi Brushless Jigsaw has a brushluss motor that creates more runtime, power, and faster cutting. It features a lock on trigger with a variable speed dial and is compatible with Ryobi's LITHIUM HP batteries for better performance.
To cut out the straight line on the coat rack sides I used my Diablo Ultra Finish Saw Blade. This saw blade is specifically designed to increase performance with each application. It features a thin laser cut kerf for durable and clean cuts and has carbide tips that can withstand extreme impact, allowing maximum durability.
Step 2: Next I used my Kreg jig to drill pocket holes into the support braces ( 1 x 4 - 22") for the plate rack. I used a 3/4" setting and 1 1/4" pocket hole screws.I used my Ryobi Drill/Driver to screw in the supports. The Ryobi Drill/Driver has a new 3-jaw chuck with a quick hex bit insert, it features a 2-speed gear box and has a brushless motor that provides 50% longer run time, extending the tool's life span.
Step 3: After the support pieces were secure I added in the (1x6 - 22") bottom shelf and attached it to the assembled plate rack using my Ryobi Brad nailer and then attached the (1x2 - 22") trim peice with brad nails to the bottom shelf.
Step 4: I then added the two additional trim pieces to the plate rack using my Ryobi Drill/Driver.
Step 5: After the coat rack was assembled I used my Bosch Spade Bits to create the holes for the 3/8" dowels and then attached the dowels using DAP Rapid Fuse Glue.
The Bosch Spade Bit set drills 10x faster than any conventional spade bit and has full thread tips that grabs the wood and pulls the bit through. Its paddle design reduces bit jamming and creates better hole entry.
once the dowels were in place she was ready for finish. I decided to try this WACO - Danish Oil for the first time and absolutely loved it. It really made the poplar pop.
Once I sanded the plate rack she was ready to be hung and man does she look good!
This fun DIY was an easy way to bring some flavor to my kitchen and I had tons f fun trying out some new tools, lets take one last look.
Thanks for reading guys. XOXO, Ashley
I acknowledge that the Home Depot is partnering with me to participate in the THD Pro-Spective Tool Review Program. As a part of the program, I am receiving compensation in the form of products and services, for the purposes of promoting The Home Depot. All expressed opinions and experiences are my own. My post complies with the Word of Mouth Marketing Association (WOMMA) Ethics Code and applicable Federal Trade Commission guidelines.